|
nugbɔ ƒe banding
Wallis ye nye esia
| Amadede: | |
|---|---|
| Nusi wotsɔ wɔe: | |
| Dɔwɔwɔ: | |
| Agbɔsɔsɔ: | |
Wallis naa PVC kple ABS J-clip edge banding profile siwo wowɔ ɖe ɖoɖo nu na xɔmenuwo dɔwɔƒewo, kabinet wɔlawo, panel processors, ememe kontraktɔ, mamalawo kple OEM dɔwo. J-nɔnɔme ƒe nɔnɔmetata si wowɔ do ŋgɔ la sɔ ɖe xɔmenuwo ƒe ʋuƒo ƒe nugbɔ si woɖe ɖe go la dzi be wòawɔ atsyɔ̃ɖoɖo ƒe liƒo dzadzɛ esime wòle kpekpem ɖe xɔmenuwo takpɔkpɔ ta tso ƒoƒo, ƒuƒu, ɖiƒoƒo kple tsi ƒe dzedzeme me.
Wotrɔ asi le eŋu na panel ƒe titrime tso 16 mm va ɖo 25 mm, Wallis J-profile edge trim ate ŋu atrɔ asi le profile ƒe didime, nu, amadede, nɔnɔme, nuwuwu kple lãɖeɖe didime. Atsyã siwo li dometɔ aɖewoe nye amadede sesẽwo, atikutsetsewo, kpe xɔasi, ga, avɔ-dzedzeme, keklẽ gã, super-matte kple xɔmenuwo ƒe anyigba ƒe nɔnɔme siwo wowɔ ɖe ɖoɖo nu.
Wotsɔa atike sia naa amewo abe J-profile si woɖe tso eme si wowɔ do ŋgɔ ene . Mele be woatɔtɔe kple flat roll edge banding dzro aɖe alo mɔ̃ si wotsɔ J-nɔnɔme softforming edging wɔ o. Ne èdi nyayɔyɔ si sɔ la, na panel la ƒe titrime, nugbɔ ƒe nɔnɔmetata, profile cross-section si hiã, eɖoɖo mɔnu kple physical board sample.
Bia J-Profile Kpɔɖeŋu kple Nyayɔyɔ
Nusiwo gbɔna ƒe nɔnɔmewo ɖe adzɔnuwo ƒe hatsotso si woɖe fia le axa sia fia. Ele be woaɖo kpe profile ƒe didime mamlɛawo, fit tolerance, didime, anyigba ƒe nuwuwu kple eɖoɖo ƒe nudidiwo dzi tso nɔnɔmetata si dzi woda asi ɖo kple ŋutilã me kpɔɖeŋu hafi woawɔe le agbɔsɔsɔ gã me.
| Mɔ̃ɖaŋununya ƒe Nyatakakawo | Asixɔxɔ si Li |
|---|---|
| Nu | PVC alo ABS |
| Board ƒe Titrime si sɔ | 16–25 mm ƒe didime; exact fit si woto vɛ le panel kple profile drawing nu |
| Profile ƒe Kekeme Kple Cross-Section | J-profile geometry si wowɔ ɖe ɖoɖo nu, nuyi ƒe goglome, tɔtrɔgbɔ ƒe didime kple mo ƒe kekeme si wokpɔna |
| Profile Gli ƒe Titrime | 0.8–1.5 mm ƒe didime; tiatia siwo wowɔ ɖe ɖoɖo nu le dɔwɔnuwo kple dɔwɔwɔ me toto te |
| Didime si Woɖo Ðe Ðoɖo Nu | 2450 mm, 2500 mm alo lãɖeɖe ƒe didime si wowɔ ɖe ɖoɖo nu |
| Anyigbadzi Nuwuwu | Matte, super-matte, ŋutigbalẽ-se le eɖokui me, gloss, gloss kɔkɔ, embossed alo etɔxɛ-ŋusẽ ƒe nuwuwu |
| Atsyɔ̃ɖoɖo ƒe Aɖaŋuwɔwɔ | Amadede sesẽ, atikutsetse, kpe xɔasi, kpe, ga, avɔ-dzedzeme kple atsyɔ̃ɖoɖo si wowɔ ɖe ɖoɖo nu |
| Eɖoɖo ɖe dɔa me | Press-fit, clip-on alo adhesive-kpekpeɖeŋu kpekpe le profile ƒe nɔnɔme kple panel nɔnɔme nu |
| Trɔ asi le eŋu | Profile tooling, didime, nusi wotsɔ wɔe, amadede, nɔnɔme, dzesi, didime, dzesidewo kple nubablɛwo |
Do ŋgɔ na J-profile nugbɔ trim si wowɔ ɖe xɔmenuwo ƒe akpata ƒe atitsoga ƒe akpa dzi
J-clip nugbɔ banding nye extruded plastic nuwuwu profile kple J-nɔnɔme cross-section. Akpa ɖeka tsyɔa ʋuƒoa ƒe go si wokpɔna la dzi esime nuyi si trɔna la xatsaa ʋuƒoa ƒe mo ƒe akpa aɖe alo léa eŋu. Geometry sia wɔa liƒo si woɖe fia, ekpɔa board la ƒe go ta eye ate ŋu atsɔ asiléƒe, frame alo atsyɔ̃ɖoɖo ƒe dzedzeme akpe ɖe xɔmenuwo ƒe akpawo ŋu.
To vovo na flat edge banding si wozãna ɖaa si wonana le agbalẽ xatsaxatsawo me la, zi geɖe la, wowɔa J-clip profile ɖe board ƒe titrime tɔxɛ aɖe nu eye wotsɔe naa wò le didime dzɔdzɔewo me. Ele be ememe ʋuʋu, nuyi ƒe tete, gli ƒe titrime kple tɔtrɔgbɔ ƒe didime nasɔ kple xɔmenuwo ƒe akpa ŋutɔŋutɔ hena eɖoɖo dedie.
Standard edge banding nye flat strip si wotsɔ hot-melt adhesive bla ɖe board edge dzɔdzɔe alo profiled ŋu. Woɖea J-clip ƒe nugbɔ xoxo wòzua atitsoga si ƒe nɔnɔme le abe atitsoga ene eye wotsɔa wo dana ɖe ʋuƒoa ƒe nugbɔ dzi. Eyata mɔ̃ siwo hiã, packing format, installation sequence kple dimensional tolerances to vovo.
Softforming zãa nusi te ŋu trɔna bɔbɔe si ƒe nugbɔ le gbadzaa kple nyaƒoɖeamenu dɔwɔnu tɔxɛ aɖe tsɔ xaa xɔmenuwo ƒe nugbɔ si wotsɔ mɔ̃ wɔe si ƒe nɔnɔme le abe J ene. Nusi wowɔ le axa sia nye PVC alo ABS nɔnɔmetata si wowɔ do ŋgɔ. Gblɔ xɔtuɖoɖo si wò dɔa zãna ale be woate ŋu ana xɔtunu kple eŋudɔwɔwɔ ŋuti aɖaŋuɖoɖo nyuitɔ.
Nɔnɔmetata si ƒe nɔnɔme le abe ʋuƒoa ene la tsyɔa ʋuƒoa ƒe go si woɖe ɖe go la dzi eye wòtrɔna yia ʋuƒoa ƒe anyime. Ne profile ƒe ʋuʋu kple nuyi ƒe didime sɔ kple board la nyuie la, J-section la wɔa xɔmenuwo ƒe go si le dzadzɛ, si li ke eye wòdzena le nukpɔkpɔ me.
PVC kple ABS ƒe nɔnɔmetatawo wɔa ametakpɔnu mɔxenu ƒo xlã MDF, particleboard, plywood, HDF kple PVC foam board ƒe go siwo ŋu woate ŋu adze afɔku le. Profile la kpena ɖe ame ŋu be wòaɖe nusiwo gblẽ le ƒoƒo siwo sɔ, abrasion, chipping kple handling le xɔmenuwo zazã me dzi akpɔtɔ.
PVC kple ABS nye dzoxɔxɔnu siwo me ʋuʋudedi mele o siwo kpena ɖe ame ŋu be tsi ƒe kadodo tẽ kple ʋuƒoa ƒe nugbɔ dzi ɖena kpɔtɔna. Tsitretsitsi si wowu enu nɔ te ɖe alesi wòsɔ, nuwuwu ƒe atikewɔwɔ, adhesive alo fixing mɔnu, dzogoe ƒe ƒunukpeƒewo kple eɖoɖo ƒe nyonyome dzi; plastic profile ɖeɖe dzaa mena xɔmenuwo ƒe akpa bliboa tsi mate ŋu age ɖe eme o.
Woate ŋu awɔ ɖeka kple mo si wokpɔna la kple xɔmenuwo ƒe filmwo, laminates, melamine panels kple atsyɔ̃ɖoɖo ƒe ʋuƒowo. Wallis doa alɔ amadede sesẽwo, atsyã siwo wota, nuŋɔŋlɔ siwo wotsɔ nuŋɔŋlɔ wɔe, ga ƒe ŋusẽkpɔɖeamedziwo kple keklẽ vovovowo hena xɔmenuwo ƒe go siwo sɔ alo esiwo to vovo.
Woateŋu awɔ profile geometry tso mɔ̃ɖaŋununya ƒe nɔnɔmetata, board sample alo trim si li xoxo me. Dɔwɔnu siwo wowɔ ɖe ɖoɖo nu ate ŋu ahiã ne ememe ʋuʋu, mo si woate ŋu akpɔ, nuyi si trɔna alo nuyi ƒe nutrenu ƒe nɔnɔme to vovo tso nɔnɔmetata si wozãna ɖaa si li gbɔ.
Trɔ asi le extruded J-profile trims na panel-nugbɔ takpɔkpɔ kple atsyɔ̃ɖoɖo
| Tiatia ƒe Nu | PVC J-Clip ƒe Nɔnɔmetata | ABS J-Clip ƒe Nɔnɔmetata |
|---|---|---|
| Viɖe Gbãtɔ | Woate ŋu atrɔ ɖe nɔnɔmewo ŋu, exɔa ga geɖe eye woate ŋu akpɔe le atsyɔ̃ɖoɖo ƒe nuwuwu vovovowo me. | Nu si me chlorine mele o si ƒe sesẽme nyo, dzoxɔxɔ ƒe tsitretsitsi kple ŋusẽkpɔɖeamedzi ƒe dɔwɔwɔ. |
| Zãzã si Bɔe | Xɔmenuwo, kabinetwo, gliwo kple atsyɔ̃ɖonuwo ƒe nɔnɔmetata siwo mexɔ asi o. | Xɔmenuwo ƒe nyonyome, asitsaƒewo ƒe xɔmenuwo kple dɔ siwo gblɔ ABS . |
| Trɔtrɔ ɖe nɔnɔmewo ŋu | Asitɔtrɔ le nɔnɔmewo ŋu nyuie; woate ŋu atrɔ asi le atikewɔwɔ kple gli ƒe titrime ŋu na nɔnɔmetata la. | Dimension ƒe liƒo nyui kple sesẽme; seɖoƒe siwo woatsɔ abɔbɔ woe nɔ te ɖe geometry dzi. |
| Atsyɔ̃ɖoɖo ƒe Tiatiawɔblɔɖe | Nu sesẽ, atikutsetse, kpe, ga, gloss, matte kple textured anyigbawo. | Atsyɔ̃ɖoɖo ƒe anyigba sesẽwo, siwo wota, matte, gloss kple tiatia aɖewo. |
| Dɔa ƒe Nyametsotso | Tia ɣeyiɣi si me asixɔxɔ, asitɔtrɔ le nɔnɔmewo ŋu kple atsyɔ̃ɖoɖo ƒe hatsotso nye nu vevitɔ. | Tia ɣeyiɣi si me nuwo ƒe ɖoɖo, ŋusẽkpɔɖeamedzi ƒe dɔwɔwɔ alo dzoxɔxɔ ƒe tsitretsitsi nye nu vevitɔ. |
Nusiwo wotsɔ wɔe ƒe nyonyome nɔ te ɖe profile cross-section, gli ƒe titrime, eɖoɖo mɔnu, xɔmenuwo ƒe nɔnɔme kple sedziwɔwɔ si hiã dzi. Da asi ɖe kpɔɖeŋu aɖe dzi le profile geometry ŋutɔŋutɔ me tsɔ wu be nàtia nu tso nɔnɔme siwo bɔ me ko.
Woate ŋu ato J-profile siwo le abe ati ene vɛ na oak, walnut, ash, teak, maple, elm kple xɔmenuwo ƒe xɔmenuwo ƒe atsyɔ̃ɖoɖo bubuwo. Be nàwɔ ɖeka pɛpɛpɛ la, tsɔ megbe ƒe amadede, nuku ƒe tata, nɔnɔme, keklẽ kple nɔnɔmetata ƒe mo si wokpɔna sɔ kple akpata ƒe kpɔɖeŋu ŋutɔŋutɔ.
Amadede siwo wozãna ɖaa kple esiwo wowɔ ɖe ɖoɖo nu dometɔ aɖewoe nye ɣi, yibɔ, aŋutiɖiɖi, beige, blɔ, amadede dzẽ kple egbegbe xɔmenuwo ƒe vɔvɔli bubuwo. Pantone alo RAL ƒe nufiamewo ateŋu ado alɔ ŋgɔyiyi gbãtɔ, gake wokafui be woada asi ɖe kpɔɖeŋu ŋutɔŋutɔ dzi hena ewɔwɔ mamlɛtɔ.
Marble kple kpe ƒe ŋusẽkpɔɖeamedziwo ateŋu awɔ ɖeka kple Calacatta, Carrara, marble yibɔ, kpe ɣi, travertine kple atsyɔ̃ɖoɖo ƒe akpa mawo tɔgbe siwo wozãna le kabinetwo, vanities, asitsaƒewo ƒe xɔmenuwo kple xɔmenuwo me.
Anyigba tɔxɛwo ate ŋu anye ga si wotsɔ brɔs wɔe, dzonu ƒe ŋusẽkpɔɖeamedziwo, lãgbalẽ ƒe dzedzeme, avɔ ƒe dzedzeme, ŋutigbalẽ ƒe seselelãme, asibidɛ ƒe dzesi si tsi tre ɖe asibidɛ ƒe dzesi ŋu, keklẽ gã kple super-matte nuwuwu. Feasibility nɔ te ɖe profile geometry, anyigba ƒe dɔwɔwɔ kple nudɔdɔ ƒe agbɔsɔsɔ dzi.
Woate ŋu atsɔ anyigba ƒe nɔnɔmewo asɔ kple xɔmenuwo ƒe filmwo, laminates kple panel decors
16 mm, 18 mm, 20 mm alo 25 mm board siwo woyɔna be woate ŋu ato vovo le lamination, coating alo surface-film zazã vɔ megbe. Dzidze akpa si wowu enu la le teƒe geɖe eye nàna eƒe titrime suetɔ, gãtɔ kple taɖodzinu ale be woate ŋu awɔ ememe profile ƒe ʋuʋu nyuie.
Ele be nɔnɔmetata la nade dzesi ʋuʋu ememetɔ, mo ƒe kekeme si woate ŋu akpɔ, J ƒe tɔtrɔgbɔ, nuyi ƒe goglome, gli ƒe titrime, didime kple nɔnɔmetata ƒe didime bliboa. Gblɔ nenye be ele be profile la nabla sesĩe, atsɔe aƒu gbe ɖe ʋuƒoa dzi alo aɖe mɔ na teƒe si woatsɔ alé nu ɖe eŋu.
Le alesi wowɔe nu la, woate ŋu atsɔ agbalẽtamɔ̃ abla J-profiles, atsɔ mɔ̃ atso wo, atsɔ aŋe si sɔ abla wo alo atsɔ nusi wotsɔ blaa nu kple nusi wotsɔ ƒoa ƒui ade wo me. Ele be woabu panel ƒe anyigba, profile material, dzoxɔxɔ kple subɔsubɔdɔ ƒe agba ŋu ne wole kpekpemɔnu tiam.
To nuwuƒe ƒe nutrenu siwo hiã, miter ƒe lãɖeɖe, akɔta ƒe ƒunukpeƒewo kple dzogoe ŋuti nyatakakawo me. Zi geɖe la, wokpɔa tsi ƒe tsitretsitsi kple nukpɔkpɔ ƒe nyonyome to profile ƒe nuwuwu kple ƒunukpeƒewo dzi tsɔ wu be woakpɔe le didime dzɔdzɔe ƒe titina.
Ele be woaɖo kpe profile fit kple installation dzi le panel ŋutɔŋutɔ si wowu enu la dzi
Woateŋu azã J-clip profiles le nuɖaƒewo, awudzraɖoƒewo, TV units, afɔkpawo, agbalẽdzraɖoƒewo, vanity units, nudzraɖoƒe xɔmenuwo kple aƒeme panel nu bubu siwo hiã atsyɔ̃ɖoɖo ƒe liƒo si woɖe fia.
Dɔ siwo wozãna zi geɖee nye ɔfis kplɔ̃wo, takpekpekplɔ̃wo, agbalẽdzraɖoƒewo, amedzrodzeƒewo, asitsaƒewo ƒe nukpɔkpɔwo, fiase me nuzazãwo kple ɖeɖefia ƒe xɔmenuwo siwo ŋu woate ŋu awɔ dɔ le edziedzi eye woate ŋu akpɔ wo dzi.
Atsyɔ̃ɖoɖo J-profiles ate ŋu awu gli-panel goawo, mamawo, feature panels kple tɔtrɔwo dome xɔmenuwo ƒe anyigba. Ga, kpe xɔasi, avɔ kple amadede sesẽ ƒe ŋusẽkpɔɖeamedzi siwo wowɔ ɖe ɖoɖo nu ate ŋu ado alɔ xɔmenuwo ƒe ɖoɖo siwo wɔ ɖeka.
Suku ƒe kplɔ̃wo, nudokpɔƒe ƒe xɔmenuwo, agbalẽdzraɖoƒe ƒe agbalẽdzraɖoƒewo kple dɔwɔƒewo ƒe nyawo gbɔ kpɔkpɔ ate ŋu akpɔ viɖe tso nɔnɔmetata si nɔa anyi didina si tsyɔa ʋuƒo ƒe go siwo ŋu woate ŋu adze afɔku le dzi eye wòwɔa nusi woate ŋu akpɔ nyuie wu la me.
Amedzrodzeƒexɔwo, xɔ siwo me wowɔa dɔ le, modzakaɖeƒe ƒe xɔmenuwo, nuɖuɖudzraƒewo ƒe xɔmenuwo kple nubabla ƒe nyawo ate ŋu azã J-profile trims siwo wowɔ ɖe ɖoɖo nu hena amadede ƒe sɔsɔ si woate ŋu agbugbɔ awɔ, ŋusẽkpɔɖeamedzi takpɔkpɔ kple dɔa ƒe atsyã tɔxɛ.
Ðo ɖa wu panel titrime, substrate, anyigba dzi nu, cross-section nutata, dzedze profile didime, hiã nu, amadede, texture, didime, agbɔsɔsɔme, ɖoɖo mɔnu kple yiyi asi.
Wallis atsɔ geometry si hiã la asɔ kple profile siwo li. Ne nɔnɔmetata si wozãna ɖaa mate ŋu ana alesi wòsɔe o la, woate ŋu ado custom extrusion tooling ƒe susu ɖa be woada asi ɖe edzi.
Do kpɔɖeŋua kpɔ le ʋuƒo ŋutɔŋutɔ si wowu enu la dzi. Kpɔ ŋusẽ si wotsɔ dea nu me, nusi léa nu ɖe te, dometsotso siwo woate ŋu akpɔ, nuyi ƒe nɔnɔme, dzogoe ƒe atikewɔwɔ, amadede ƒe sɔsɔ, anyigba ƒe nyonyome, dzɔdzɔenyenye kple nulénu alo nusi wotsɔ léa nu ɖe te ƒe mɔnu si nètia.
Kpe ɖe profile ƒe nɔnɔmetata, kpɔɖeŋu si dzi woda asi ɖo, nusi wotsɔ wɔe, nuwuwu, didime ƒe mɔɖeɖe, babla kple ŋkuléle ɖe nudidiwo ŋu dzi. Ele be nɔnɔmetata si wode asi na kple master sample nakpɔ ewɔwɔ gbugbɔgawɔ dzi.
Ðo Wò Profile Drawing alo Board Sample ɖa
Profile ƒe dɔwɔwɔ nɔ te ɖe didime ƒe ɖekawɔwɔ kpakple atsyɔ̃ɖoɖo ƒe nyonyome dzi. Ele be woatu ŋkuléleɖenuŋu ɖe nɔnɔmetata si dzi woda asi ɖo, nusiwo wotsɔ wɔe ƒe nɔnɔme kple master sample dzi.
Profile ƒe didime: ememe ʋuʋu, mo si woate ŋu akpɔ, nuyi si trɔ gbɔ, gli ƒe titrime kple cross-section bliboa.
Didime kple dzɔdzɔenyenye: lãɖeɖe ƒe didime, warpage, twist kple nudzraɖoƒe ƒe nɔnɔme.
Fit performance: insertion force, retention, dometsotsowo kple ɖekawɔwɔ kple board si dzi woda asi ɖo.
Anyigba ƒe nyonyome: amadede, keklẽ, tata, embossing, ŋlɔmiwɔwɔ, ɖiƒoƒo kple nɔnɔme madeamedzi siwo woate ŋu akpɔ.
Mɔ̃ɖaŋununya ƒe nuwɔna: asitɔtrɔ le nɔnɔmewo ŋu, ŋusẽkpɔɖeamedzi ƒe nuwɔna kple gbagbã le dodokpɔmɔnu si dzi wolɔ̃ ɖo nu.
Nubablɛ: didime takpɔnu, bablawo, ŋkɔwo, kakɛwo alo palletwo kple meliɖoɖo ƒe dzesiwo.
Wallis ate ŋu awɔ ɖeka kple extrusion geometry kple furniture-surface design. Dɔa ate ŋu aƒo dɔwɔnu siwo wowɔ ɖe ɖoɖo nu le nɔnɔmetatawo ŋu, amadede sesẽwo ƒe sɔsɔ, atsyɔ̃ɖoɖo ƒe agbalẽtata, nuŋɔŋlɔ kple anyigba ƒe nuwuwu nu ƒu ɖekae le ŋgɔyiyi ƒe ɖoɖo ɖeka me.
Nuƒlelawo ateŋu atia PVC na aɖaŋu si keke ta ƒe asitɔtrɔ kple ewɔwɔ si me gazazã mele o alo ABS na nɔnɔmetata si me chlorine mele o si ƒe sesẽme nyo eye wòte ŋu nɔa te ɖe dzoxɔxɔ nu. Wotoa nusiwo woatsɔ awɔ dɔe ƒe tiatia me tsɔ sɔ kple alesi wotso woe ŋutɔŋutɔ kple alesi wozãe.
Wallis doa alɔ didime siwo wowɔ ɖe ɖoɖo nu, babla ƒe agbɔsɔsɔme, dzesidewo, kakɛ ƒe dzesiwo, ametakpɔnu bablawo kple dɔdɔ ɖa ƒe ɖoɖowɔwɔ na xɔmenuwo dɔwɔƒewo, profile mamalawo kple ememe dɔa ƒlelawo.
Wallis ƒe ɖaseɖigbalẽwo kple nyonyome ŋuti nuŋlɔɖiwo
Wallis doa alɔ xɔmenuwo wɔlawo, kabinet dɔwɔƒewo, xɔtunuwo mamalawo, panel processors kple project contractors le dukɔwo dome asiwo me. Mɔ̃ɖaŋunutatawo, kpɔɖeŋu siwo dzi woda asi ɖo kple nubablɛ ƒe nɔnɔme siwo me kɔ kpena ɖe ame ŋu be woaɖe profile-fit kuxiwo kple tɔtrɔ si wogbugbɔ ɖoa nudɔdɔ dzi kpɔtɔna.
Nuwɔwɔ ƒe ɖoɖowɔwɔ kple dukɔwo dome B2B ƒe kpekpeɖeŋu
Dekɔnu extruded profiles ate ŋu abia zi geɖe ƒoƒo zi geɖe le nutata me toto, dɔwɔnu, fitting kple atsyɔ̃ɖoɖo ƒe mɔɖeɖe. Wallis léa fɔ ɖe mɔ̃ɖaŋununya ƒe kadodo si me kɔ, master-sample dziɖuɖu kple ewɔwɔ gbugbɔgawɔ si li ke ŋu hena xɔmenuwo ƒe ɖoɖowo wɔwɔ ɣeyiɣi didi.
Enye plastic extrusion si wowɔ do ŋgɔ si ƒe cross-section le abe J ene si sɔ ɖe furniture-panel ƒe go dzi. Etsyɔa ʋuƒo si woɖe ɖe go la dzi, etsɔa atsyɔ̃ɖoɖo ƒe liƒo kpena ɖe eŋu eye wòkpena ɖe ame ŋu be wòakpɔ nugbɔa ta tso eƒe ƒoƒo kple tsi ƒe ƒoƒo me.
Ao, nugbɔ ƒe banding dzrowo nye lãgbalẽ gbadzɛ si wotsɔna naa zi geɖe le agbalẽ xatsaxatsawo me eye woblanɛ ɖe ʋuƒo ƒe nugbɔ ŋu. Wotsɔa J-clip edging naa abe nɔnɔme ƒe nɔnɔmetata ene le didime dzɔdzɔewo me eye ele be wòasɔ kple panel ƒe titrime kple cross-section.
Ao, Softforming zãa nugbɔ gbadza si te ŋu trɔna bɔbɔe kple mɔ̃ tɔxɛwo tsɔ blaa akpa si wotsɔ mɔ̃ wɔe si ƒe nɔnɔme le abe J ene. Adzɔnu sia nye J-profile si woɖe do ŋgɔ si woda ɖe panel la ƒe go kemɛ dzi.
PVC nye esi te ŋu trɔna bɔbɔe, mexɔa ga geɖe o eye wòle amadede vovovowo kple atsyɔ̃ɖoɖo ƒe nɔnɔme vovovowo me. ABS nye esi me chlorine mele o eye wònaa sesẽme nyui, didime ƒe liƒo kple dzoxɔxɔ ƒe tsitretsitsi. Tiatia nyuitɔ nɔ te ɖe profile geometry, dɔwɔwɔ kple asi si woɖo taɖodzinu na dzi.
Woateŋu atrɔ asi le wo ŋu na MDF, particleboard, plywood, HDF, PVC foam board, melamine-faced boards kple laminated furniture panels. Ele be ememe profile ƒe ʋuʋu nasɔ kple board si wowu enu ƒe titrime ŋutɔŋutɔ.
Woate ŋu anye esi woate ŋu atsɔe aɖoe, woate ŋu atsɔe ablae, woatsɔe akpe ɖe nulénu ŋu alo woatsɔe aƒo ƒui, le profile ƒe nɔnɔme kple xɔmenuwo ƒe nɔnɔme nu. Ele be woado mɔnu si wodo ɖa la kpɔ le ʋuƒo ŋutɔŋutɔ dzi hafi woawɔe le agbɔsɔsɔ gã me.
Profile geometries kple material formulations aɖewo ate ŋu axɔ curves fafɛ, gake rigid straight-length profiles ƒe bending radius suetɔ kekeake le esi. Na curve radius kple application drawing ale be woateŋu ada feasibility kpɔ.
Ɛ̃. Wallis ateŋu awɔ amadede siwo wɔ ɖeka, ati nuku, kpe, ga, avɔ kple etɔxɛ-ŋusẽ ƒe anyigba siwo wotu ɖe ŋutilã me xɔmenuwo film, laminate alo panel kpɔɖeŋu dzi.
Ɛ̃. Woate ŋu atrɔ asi le ememe ʋuʋu, mo si wokpɔna, J trɔ gbɔ, nuyi ƒe goglome, gli ƒe titrime kple lãɖeɖe ƒe didime ŋu. Ðewohĩ ahiã be woawɔ extrusion die yeye na cross-sections siwo menye standard o.
Na panel si wowu enu ƒe titrime suetɔ, gãtɔ kple taɖodzinu, anyigba ƒe xɔtutu, nugbɔ ƒe nɔnɔme kple didime ƒe nɔnɔmetata. Wokafui be woaɖo physical board sample ɖa be woatsɔ aɖo kpe edzi be esɔ.
Ɛ̃. Woate ŋu awɔ ɖoɖo ɖe kpɔɖeŋuwo ŋu hena didime ƒe sɔsɔ, wo ɖoɖo, wo léle ɖe te, amadede, nɔnɔme kple anyigba ƒe nyonyome ƒe dodokpɔ. Dɔwɔnu siwo wowɔ ɖe ɖoɖo nu ƒe kpɔɖeŋuwo nɔ te ɖe dɔwɔnuwo ƒe mɔɖeɖe kple dɔa ƒe nudidiwo dzi.
Ðo profile ƒe nɔnɔmetata, panel ƒe titrime, substrate, nusi nèdi, didime siwo woate ŋu akpɔ, didime, amadede alo panel ƒe kpɔɖeŋu, nuwuwu, eɖoɖo mɔnu, agbɔsɔsɔme, packing nudidiwo, dukɔ si me nèyina kple dodokpɔ alo sedziwɔwɔ ŋuti nuŋlɔɖi siwo hiã.
