|
Wallis PETG offset lomi pepa lagolago ID, faletupe ma le gaosiga o kata atamai ma fua masani, autu ma Ata overlay filifiliga, vaitusi ma lamination su'ega, fa'ata'ita'iga ma sapalai B2B sa'o ile falegaosimea.
WLS- PETG Pepa Offset
WALLIS
| Lanu: | |
|---|---|
| Mafiafia: | |
| Aofa'i: | |
Wallis PETG offset lomi pepa ua atia'e mo tagata fai pepa ID, fale gaosi kata atamai, fai pepa totogi, tagata e maua avanoa, lomitusi pepa ma tufatufa mea e mana'omia ai le mafai ona lolomi offset mautu, malosi lamination fa'atinoga ma fa'atuatuaina fa'apipi'i pepa fa'apipi'i. O pepa pa'epa'e, manino ma fa'apitoa PETG e mafai ona tu'uina atu e mafai ona fa'apipi'iina i luga ole laiga autu, papa lagolago, fa'alava fa'apipi'i ma manino Ata overlay s.
PETG gaosiga o kata ose faiga faiga. O le mafiafia o pepa, malosi i luga, kemisi vaitusi, fa'agogo, fa'amau lolomi, vevela lamination, mamafa, mālūlū, RFID mafiafia fa'alava, laina fa'amaneta ma fua fa'ai'uga pepa e tatau ona fa'amaonia fa'atasi. Ua fautuaina e Wallis ia su'ega lolomi-ma-lamination a'o le'i faia le tele o oka, aemaise lava mo kata totogi, kata e leai ni feso'ota'iga ma fa'amaoniga umi o le olaga.
PETG e mafai ona ofoina atu le manino maualuga, faigata ma le lelei o le fusifusia vevela, ae o tagi lautele e pei o le ' fetaui ma so'o se lomitusi offset, ' ' lima tausaga kata ola, ' ' UV -proof' poʻo le 'pepa toe faʻaaogaina atoatoa' e manaʻomia ai faʻamaoniga mai le fausiaina tonu. O le kata atoa—e le gata o le pepa mata PETG —e tatau ona fetaui ma manaoga o le tagata faatau, masini, eletise ma le siosiomaga.
| Ituaiga Oloa | PETG offset pepa autu e mafai ona lolomi ma mea manino Ata overlay mo kata fa'apipi'i tele |
| Oloa Aiga Mafiafia | 0.05–0.80mm e fa'atatau ile autu, Ata overlay , lanu ma fa'asologa masani |
| PETG Mafiafia Autu | 0.095–0.40mm PETG pepa autu e mafai ona lolomiina |
| PETG Ata overlay Mafiafia | 0.06–0.10mm PETG manino Ata overlay |
| Metotia Lomitusi | Offset ma silk-screen lomitusi; UV numera po'o isi faiga e mana'omia ai le fa'ailoga o luga ma vaitusi |
| Talosaga | ID, avanoa, sui auai, ki faletalimalo, felauaiga, faletupe, faamaoni, meaalofa, RFID ma kata IC |
| B2B Lagolago | Fa'ata'ita'iga, fua fa'aleaganu'u ma lapo'a, su'ega vaitusi, su'ega lamination, iloiloga fa'atulagaina o pepa, fa'amatalaga QC ma sapalai fa'atau atu. |
Talosaga PETG Pepa Fa'ata'ita'iga ma Fa'amatalaga
PETG o se polyester ua suia glycol o lo'o fa'aogaina i fa'aata manino ma le opaque card. Mo le gaosiga o kata offset, PETG pepa e tatau ona maua ai le mafiafia pulea, mafolafola, malosi i luga, pa'epa'e po'o le manino, tulaga mautu ma le fa'apipi'i vevela. E mafai e le laupepa ona ave ata lolomi pe fai fo'i se vaega o le fausaga ma le puipui puipui o se kata ua mae'a.
PETG kemisi i luga e ese mai pepa ma PVC . Susū vaitusi, maileia, fa'agogo ma le pipi'i e fa'alagolago i le togafitiga o luga, fa'alavelave i luga, faiga vaitusi ma tulaga lolomi. O le itu e mafai ona lolomiina e tatau ona iloa lelei, ma e tatau ona siaki le maualuga o togafitiga aʻo leʻi lolomiina.
O le PETG laupepa autu e maua ai le lagolago lolomi, opacity ma le mafiafia fausaga. O le PETG Ata overlay e masani lava ona manino ma puipuia le laulau lolomi pe a uma ona lamination. O le mafiafia, malosi i luga o le fogaeleele, malosi faʻamalosi, mamafa ma le tali vevela e tatau ona faʻamaonia eseese.
O fa'amaumauga mata'utia e le'o fa'amaonia ai le olaga fa'auma. Pi'o, torsion, abrasion, tete'e vaila'au, poloka, warpage, mautu vevela, adhesion layer ma galuega eletise e tatau ona tofotofoina i luga o le pepa atoa lolomi, laminated, tu'i ma patino.
Fa'agasologa Lomitusi Offset
Fa'ata'ita'i Ata Fa'ai'uga Maualuga
O tau nei o fa'amatalaga fa'asino mo PETG mea pepa pepa. O faʻamatalaga mulimuli e tatau ona faʻamaonia e tusa ai ma le tulaga saʻo o oloa, faʻataʻitaʻiga o suʻega talafeagai, faʻatulagaina, faʻapalepale ma tusi pasi.
| Meatotino | PETG Fa'asinomaga Autu | PETG Ata overlay Fa'amatalaga | B2B Fa'atauga Fa'amatalaga |
|---|---|---|---|
| mafiafia | 0.095–0.40mm | 0.06–0.10mm | Fa'amaonia le averesi, fa'apalepale fa'asino-i-itu ma le fesuiaiga o le tele |
| Tete'e i luga | ≥38 dynes/cm | ≥36 dynes/cm i luga ole itu lolomi | Talitonu metotia su'ega, itu togafitia ma le maualuga o le taimi e teu ai a'o le'i lolomiina |
| Malosi Tetele | ≥40MPa | ≥38MPa | Faʻamaonia le faʻatonuga, faʻataʻitaʻiga saoasaoa, faʻatulagaina ma tulaga masani |
| Malosi | 1.30 ± 0.05g/cm³ | 1.27 ± 0.05g/cm³ | Fa'aoga mo le fa'ailoaina o meafaitino ma le fuafuaina o le mamafa, ae le na'o le pau lea o le tulaga lelei |
| Vicat A120 | 78 ± 2°C | 76 ± 2°C | Vicat e le o se lamination tuusaʻo poʻo le faʻatapulaʻaina o le vevela |
| Galuega masani | Laupapa lomitusi, fa'apipi'i kata po'o le fa'avae fa'avae | Puipuia Ata overlay mo PETG , PVC po'o kata tu'ufa'atasi talafeagai | Fa'amaonia le fusifusia ma le matua o le si'osi'omaga mo le tu'ufa'atasiga sa'o |
Papa'e Lomi PETG Autu
Kata-Vaega PETG Mea
Autu ma Ata overlay Filifiliga
| Ata Ata | PETG Pepa autū | PETG Ata overlay |
|---|---|---|
| Matafaioi Muamua | Lomiina ata, opacity, mafiafia ma lagolago faʻavae | Puipuiga manino, fa'ai'uga i luga ma lolomi fa'amau |
| Foliga Fa'atusa | Pa'epa'e, opaque, translucent po'o lanu masani | I'ila manino, matte, aisa po'o fa'auma fa'apitoa |
| Lomitusi | E masani ona offset pe lolomi lau | E masani lava ona le lolomia le puipuiga; lolomi fa'apitoa Ata overlay mana'omia le fa'amaoniga |
| Lamination | E tatau ona feso'ota'i ma Ata overlay , fa'apipi'i ma isi fa'avae autu | E tatau ona maua ai le pipii mautu e aunoa ma le puaoa, pulupulu po'o le pa'u |
| QC Taulai | Mafiafia, lanu, opacity, tete'e i luga, mafolafola ma lolomi | Malamalama, puaoa, i'ila, fua, fusi, abrasion ma masi'i fa'atinoga |
O kata fa'apolofesa e masani lava ona fausia mai le tele o laulau. Ole ISO /IEC 7810 o lo'o iai nei o lo'o fa'amaoti mai ai uiga fa'aletino mo kata e iloagofie ai, ae o le fa'asologa masani ID-1 e tusa ma le 85.60 × 53.98mm fa'atasi ai ma le mafiafia fa'atatau ile 0.76mm. Ole fa'aputu sa'o PETG e tatau ona fa'atatau mo 'au lolomi, manino Ata overlay s, fa'apipi'i, RFID inlays, chip modules, maneta ta'avale ma fa'amalosi i le taimi o lamination.
| Layer | Fa'atonu Fa'atino | PETG Pulea Poloketi |
|---|---|---|
| Luma Ata overlay | Puipuia galuega taulima ma pulea le iila po'o le mae'a mae'a | Malamalama, fa'amau, abrasion, fa'asinomaga ma feso'ota'iga fa'amaneta |
| Ulu lolomi Core | O lo'o tauaveina lanu o fa'agasologa, tagavai, tusitusiga ma galuega tau le puipuiga | Fa'apipi'i vaitusi, fa'agogo, lomitusi ma fa'amautu le fua |
| Autu Tutotonu / Inlay | Fausia le mafiafia ma e ono iai RFID antenna po'o le pu | Inlay mafiafia, ana, fa'asoa fa'amalosi ma le fa'atinoga o le eletise |
| Autu Lolomi tua | Fa'ata fa'afeagai ma fa'apa paleni | Fa'afetaui le mafiafia pito i luma ma lolomi le ufiufi pe a mafai e fa'aitiitia ai le fa'afefe |
| Tua Ata overlay | Puipuia le lolomi ma lagolagoina le saini laupapa po'o le laina filifiliga | Paleni, faʻapipiʻi, faʻailoga ma manaʻoga faʻapitoa |
Fua le tutusa i luma ma tua, fa'apipi'i lolomi po'o mea fa'afefiloi e mafai ona fa'atupuina ai le fa'amamafa ma le pi'o. Fa'aoga fausaga fa'atusa pe'ā mafai ma fua le mafolafola pe a mae'a ona mālūlū ma fa'amalie le kata.
O le mamafa, fa'aitiitia, vaitusi, tafega pipii, fa'amaneta ma mea fa'aeletoroni e a'afia ai le i'uga mulimuli. E tatau ona fuaina le mafiafia o pepa fa'auma pe a uma ona lamination, fa'alili, tu'i ma fa'amalo.
| Fautuaina Fa'ata'ita'i | B2B Pepa Pepa. |
|---|---|
| Fa'amaoniga i luga | Fa'ailoa le itu e mafai ona lolomi, fua le malosi o luga ma siaki pe pefu, suauu, maosiosia po'o togafitiga pala |
| Lomi ma Fafaga Seti | Fa'amautu le mafiafia o le laupepa, malo, fa'atonuga, fa'amau fa'amau, ea fafaga ma le fa'aputuina |
| Faiga vaitusi | Fa'aaogā vaitusi ua fa'atūina mo le palasitika e le fa'afefe ma fa'amaonia le pipii, fa'agogo, fetuutuuna'i ma le lamination. |
| Vai ma Vaitusi Paleni | Pulea vaipuna vaifofo e faʻaitiitia ai le emulsification, faʻagogo tuai ma faʻaletonu ata |
| Fa'avasega lanu | Fa'aaogā fa'amaoniga fa'amaonia, fa'amautu fa'amau, fa'asinoga Pantone ma le fa'atonutonuina o le lanu o le substrate |
| Tiliva ma Fa'aputu | Fa'atapula'a le mamafa o fa'aputuga, fa'aaoga faiga e fa'ato'a fa'agata ma 'alofia le poloka po'o le fa'aliliuina o ata |
E le pipi'i pe mago sa'o le vaitusi o pepa i PETG . E tatau i tagata fa'atau ona fa'amaonia le oxidative, UV -e mafai ona togafitia po'o isi faiga vaitusi palasitika fa'atasi ma le vaitusi ma lomitusi fa'atau, ona su'e lea o le pepa lolomi e ala i lamination.
O itu uma e lua e mafai ona lolomi pe a fetaui le laupepa ma le lolomi galuega. O le vaitusi pito muamua e tatau ona lava lelei ona fofo a'o le'i pasi lona lua, ma o ata mai luma i tua e tatau ona faapaleni e faaitiitia ai le pi'o ma le lanu.
| Fa'atatauga | Su'ega |
|---|---|
| Fa'apipi'i Fa'amau | Siaki le fusi o luga pe a maeʻa le faʻamagoina poʻo le taimi faʻamalolo |
| Mili ma Usu | Iloilo le taulimaina a'o le'i lamination ma fa'auma-kati tumau pe a uma lamination |
| poloka poloka | Siaki le fa'aliliuina o ata i lalo o le mamafa o le faaputuga, taimi ma le vevela |
| Su'ega vevela Lamination | Siaki le suiga o lanu, femalagaiga o vaitusi, fa'afefete ma pipii pe a uma le taamilosaga vevela atoa |
| Tete'e vaila'au | Iloilo le ava malosi, fa'amama, palasitika, fa'apipi'i ma isi feso'ota'iga talafeagai |
| Siaki lanu ma Barcode | Fa'amaonia ata, tusitusiga lelei, QR codes ma barcodes e mafai ona faitau pe a uma |
Fa'atatau PETG fa'apipi'i e mafai ona pipii fa'amama i le taimi o lamination card, fa'aitiitia ai le fa'alagolago i mea fa'apipi'i masani. Peita'i, e le tatau ona fa'apea le fa'apipi'iina e aunoa ma se pipii mo vasega uma PETG , vaitusi lolomi, PVC lapisi, RFID fa'apipi'i po'o fa'amea fa'afefiloi. Fa'ata'ita'iga su'ega pa'u e mana'omia.
Fa'alelei mea e fa'aoga: Fa'amautu pepa autu, Ata overlay s, fa'apalapala lolomi ma fa'alava i le vevela ma le susu.
Fa'amautu le fa'atonuga: Fa'amaumau le fa'atonuga o masini, fa'asaga fa'afeagai, itu fa'ata'ita'i ma itu lomitusi mo vaega ta'itasi.
Fausia se faaputuga paleni: Faafetaui i luma ma tua fua ma faʻamau mo tupe meataalo, antennas, taʻavale ma saini panels.
Fa'atino se fa'ata'ita'iga o le vevela: Fa'ailoa le vevela aupito maualalo, mamafa ma le fale e maua ai le so'oga ma le mafolafola talafeagai.
Fa'alili i lalo o le mamafa fa'atonutonu: O le mālūlū e a'afia ai le mautu, puao, fa'amamafa o totoe ma le poloka.
Tulaga a'o le'i fuaina: Siaki le mafiafia, fa'aiti'itia, taua, pa'u malosi ma foliga mai pe a uma ona toe fa'aleleia.
Loka le fua fa'amaonia: Fa'amau le fa'auma ipu, fa'amalo ata, fa'aputu fa'asologa, fa'amatalaga vevela, mamafa, taimi ma le mālūlū.
PETG ma le PVC e mafai ona fa'aoga i fa'atulagaga pepa tu'ufa'atasia, ae o eseesega i le fa'amaluluina, fa'aiti'itia ma le kemisi i luga e ono fa'atupu ai le pipi'i, puao po'o le fa'avaivai vaivai. E mana'omia se fa'a fusiua po'o se ufiufi Ata overlay mo nisi tu'ufa'atasiga.
E fesoasoani fa'amatalaga Vicat e fa'atusatusa uiga fa'amalulu meafaitino ae le fa'atatau tonu i le vevela o le lomitusi. E tatau ona fa'ata'ita'i fa'ata'ita'i le fe'avea'i o le vevela e ala i le fa'aputu uma o kata, mamafa, nofo, vevela ipu ma le mālūlū.
| Card Type | PETG Material Focus | Critical Validation |
|---|---|---|
| Pepa ID Tagata faigaluega ma tamaiti aoga | Papa'e e mafai ona lolomi ma manino Ata overlay | Aulelei ata, fetu'una'i i aso uma, abrasion ma fa'asinomaga |
| Avanoa ma Hotel Key Cards | E mafai ona lolomi PETG 'au fa'atasi ma le fa'amaneta po'o le RFID fa'apipi'i | Loka feso'ota'iga, fa'ailoga, galuega faitau ma fa'aauau le taulimaina |
| Fa'aui, Fa'amaoni ma Pepa Meaalofa | Lomi offset maualuga, lanu masani ma fa'auma Ata overlay totogi | Lanu lanu, barcode, tete'e masima ma atotupe tumau |
| Totogi ma Pepa Faletupe | Fa'atonuga fa'apipi'i fa'apipi'i fa'atasi ma le pu, laina ma le lomitusi mautu | Fa'atatauina totogi-feso'ota'iga, chip-module ma fa'auma fa'ailoga kata |
| Felauaiga ma Campus Cards | RFID / NFC fausaga e lolomi umi ma Ata overlay fa'alava | Ta'amilosaga maualuga o fefa'atauaiga, fa'amaoni antenna, fa'asologa o tagata faitau ma le soifua matua o le si'osi'omaga |
Talosaga ID ma Avanoa Card
Poloketi Faletupe ma Pepa Totogi
| Component | PETG Card Design Mana'oga |
|---|---|
| Chip le fa'afeso'ota'i | Fa'amaonia le fa'ata'ita'iga chip, taimi, manatua, protocol, lamination-vevela fa'atapula'a ma fa'asologa fa'asologa |
| Antenna | Puipuia le geometry o le ta'ita'i mai le mamafa, tu'i ma le tipiina o le kata |
| Inlay ua mua ona laminate | Fa'afetaui mea, mafiafia, lapo'a, mea fa'apipi'i ma fa'amama fa'amama fa'atasi ma PETG apa. |
| Fa'afeso'ota'i Chip Module | Pulea le viliina o kata-tino, fua o le lua, fa'apipi'i module ma le mafolafola o luga |
| Lisi maneta | Filifili le LoCo po'o le HiCo stripe, Ata overlay fau, laina laina, fa'ailoga ma le abrasion mana'omia |
| Su'ega Fa'atino | Faitau, tusi ma fa'aigoa a'o le'i lamination, pe a uma le lamination, pe a uma tu'i ma pe a mae'a su'ega fa'alelei |
RFID ma Kata atamai Fauga
Fa'auma Laminated PETG Cards
| Fa'agasologa | Tulaga Tulaga Tulaga |
|---|---|
| Ootiina Pepa | Umi, lautele, sikuea, resitala lolomi, pito mama ma fa'aputuga fa'aputu |
| Tu'i pepa | Fua o kata, tulimanu tulimanu, burrs, pa'epa'e, ta'e ma le vaeluaga |
| Tu'i Slot ma Pu | Tulaga, kilia antenna, mamao o le pito ma le fa'atautau o uta |
| Thermal/Retransfer Personalization | O felauaiga a le lomitusi, lipine lipine, fa'ai'u i luga, fa'alavelave vevela ma le tumau o ata |
| Embossing po'o Foil Stamping | Fa'aliga ma'ale'ale pepa-tino, vevela, mamafa, fusi pepa, ta'e ma mafai ona faitau |
| Barcode / QR / Fa'ailoga | Fa'ata'ita'i faitau, sa'o fa'amaumauga, fa'ailoga fa'ailoga ma galuega pe a uma le fa'amamafa |
| Mea | Lelei | Autu Fa'atapula'a. |
|---|---|---|
| PETG | E manino lelei, ma'a'a'a, mafai ona lolomi fa'aletonu ma so'otaga fa'avevela malosi i fausaga fetaui | E mana'omia le vaitusi agavaa, fa'atonuga o fa'agasologa ma fa'apitoa toe fa'aaogā fa'apitoa mo kata ua mae'a |
| PVC | Fa'atūina faiga fa'akomepiuta, fa'avae lautele fa'atau, lolomi fa'a-offset masani ma le lelei o tau | Fa'aitiitia le fa'afefe o le vevela ma se fa'ailoga si'osi'omaga 'ese'ese ona o le kemisi polymer o lo'o iai chlorine |
| Polycarbonate | Tete'e vevela maualuga, malosi aafiaga ma leisa-tagata gafatia gafatia i togi tuuto | E sili atu le tau o meafaitino ma le gaosiga; tulaga lomitusi eseese ma lamination |
| Toe fa'aaogaina PETG / RPET G | E mafai ona fa'aitiitia le mana'omia o le resini pe'ā fa'amaonia mea e toe fa'aaogaina | Lanu, faʻaleagaina, manino, mea faʻainisinia ma le lautele o tusi faamaonia e manaʻomia le pulea |
PETG ose fa'agata ma e ono mafai ona toe fa'aaogaina i se fa'aputuga fa'apitoa e aoina ma fa'agaoioiga. E le fa'apea o pepa uma PETG ua mae'a e mafai ona toe fa'aaogaina. Inks, Ata overlay s, mea fa'apipi'i, chips, antennas, fa'afeso'ota'i modules, ta'avale fa'amaneta ma masini saogalemu e mafai ona fa'alavelaveina le fa'avasegaina ma le toe fa'aleleia.
| Talosaga | B2B Fa'amatalaga |
|---|---|
| Toe fa'aaogaina Pepa PETG | Fa'atekinisi fa'agaioiina i se PETG -fesoasoani ala; e tatau ona fa'amaonia le taliaina i le lotoifale |
| Pepa Fa'auma toe fa'aaogaina | Manaomia le iloiloga o laulau uma, vaitusi, mea fa'aeletonika ma polokalame fa'aleleia kata fa'apitonu'u |
| PVC -Saoloto | E na'o le aoga pe a leai se PVC |
| Fa'aiti'itia tulagavae kaponi | Manaomia faʻamatalaga faʻataʻitaʻiga o le olaga faʻatusatusa mea saʻo, gaosiga, ola tautua, felauaiga ma le lafoaia. |
| Mea e toe fa'aaogaina | Fa'ailoa le pasene, puna'oa, fa'apaleni fa'atele po'o le fa'aogaina o le tino ma le lautele o tusipasi |
| Mea | Fautuaina Pulea |
|---|---|
| Fa'amatalaga Mafiafia | Fua fua, fesuia'i-pepa fela'ua'i, fa'apalepale togi ma le fa'amautu |
| Fua o Pepa | Umi, lautele, sikuea, tipi saʻo ma le lelei pito |
| Mafolafola ma Pi'i | Aufana, si'i le pito, fa'atonuga ma le toe fa'aleleia pe a mae'a fa'amau |
| Lanu ma le Optical Quality | Pa'epa'e, L*a*b*, opacity, puao, manino, iila ma le tulaga fa'amaonia va'aia |
| Laufanua ma Togafitiga | Tete'e i luga, itu e mafai ona lolomi, maosiosia, fa'aleagaina, gels, lanu uliuli ma mea |
| Su'ega Lolomi Offset | Susū vaitusi, mafiafia, maileia, pipii, fa'agogo, poloka, tusitusiga lelei ma le lanu |
| Tofotofoga Lamination | Malosi o le pa'u, pua'a, pua'a, fa'aiti'itia, fa'ailoga, suiga lanu ma fa'asa'oloto ipu |
| Ua uma le su'ega o pepa | Fua, mafiafia, punou, torsion, abrasion, vevela, vailaʻau ma le eletise |
| Su'esu'e | Fa'ailoga oloa, pusa resini, aso gaosiga, pepa lotoa, itu togafitia ma lipoti asiasiga |
Stable PETG card-sheet sapalai e mana'omia le pulea lelei o mea mata, extrusion po'o le kalena, mata'ituina le mafiafia, togafiti i luga, fa'atonutonu lanu, tipi, fa'amama mama ma fa'aputuga su'esu'e. Ole gaosiga tele e tatau ona faʻatusatusa i se faʻataʻitaʻiga saini ma faʻamatalaga tusitusia.
PETG Gaosiga Pepa Pepa ma le Pulea Lelei
Teu fa'amaufa'ailoga PETG laupepa mafolafola i totonu o se faleteuoloa mama, mago ma pulea le vevela.
Taofi mea mai le susulu o le la, mea vevela, taualuga vevela ma pusa vevela.
Puipuia mea e mafai ona lolomi ma opitika mai tamatamai lima, suauu, pefu, maosi ma abrasion.
Aloese mai le lagolago fata e le tutusa ma le mamafa tele o le fa'aputuga e ono fa'apupulaina pe poloka.
Tulaga pepa i totonu o le potu lomitusi a'o le'i lolomi po'o lamination pe a eseese tulaga o faleteuoloa.
Fa'aaogā fa'alava puipui puipui, afifi fa'asa'o, fa'amau fa'amalosi ma palleti fa'atau atu.
Fa'aoga le su'esu'ega muamua-i totonu, muamua-fa'i fafo ma toe siaki le malosi i luga ole laiga pe'a uma ona teuina.
Teuga Puipuia Flat
Fa'atonu-pulea Fa'amaumauga
Sauniuniga Sapalai i fafo
Puipui Puipuia mo Poloaiga Fa'avaomalo B2B
Card-industry specialization: Pepa Autu, Ata overlay , inlay, lomitusi ma lamination e mafai ona toe iloiloina o se tasi o faiga gaosiga.
O le mafiafia ma le lapopo'a fa'apitoa: PETG pepa e mafai ona tu'uina atu mo fa'aputu kata eseese, lomitusi ma fa'atonuga tu'u.
Lagolago lomitusi offset: E mafai ona suʻesuʻeina faʻataʻitaʻiga mo le malosi i luga, faʻapipiʻi vaitusi, faʻamago, lanu ma le faʻatinoina o le lamination.
Autu ma Ata overlay filifiliga: Pa'epa'e, manino, matte, iila ma fa'apolokalame PETG laulau e mafai ona talanoaina.
Tu'ufa'atasiga o kata atamai: RFID fa'apipi'i, module chip, laina fa'amaneta ma su'ega fa'auma-kata e mafai ona aofia i le atina'e.
Fa'atosina-sa'o B2B sapalai: E talafeagai mo fale gaosi kata, lomitusi, liliu, fa'apipi'i faiga, fa'aulufale mai ma tufatufa.
Talosaga pepa, ola tautua faamoemoeina ma maketi e taunuu i ai.
Fa'a mana'omia: 'olo e mafai ona lolomi, 'au totonugalemu, fa'alilo Ata overlay po'o le apa fa'apitoa.
Mafiafia, fa'apalepale, lapo'a laupepa, fa'asologa ma le aofa'i.
Pa'epa'e, manino, felanulanua'i po'o lanu masani ma mea e mana'omia.
Fa'ata'ita'i lomitusi Offset, faiga vaitusi, UV po'o le fa'amālōlōina masani ma le fa'asalalauina o galuega taulima.
Lamination lomitusi, fausaga faʻapipiʻi, vevela, mamafa, nofo, malulu ma faʻamaeʻa ipu.
Ua mae'a le tele o kata, mafiafia, tulimanu tulimanu ma tulaga mana'omia.
RFID chip, antenna, inlay, fa'afeso'ota'i module, laina fa'amaneta po'o saini laupapa.
REACH , RoHS , mea toe fa'aaogaina, lipoti o asiasiga po'o isi fa'amaumauga e mana'omia.
Fa'ata'ita'iga aofa'i, fa'ata'ita'iga fa'aletausaga, taulaga e taunu'u i ai, fa'apipi'i ma fa'asologa o le tu'uina atu.
Talanoa i Lau PETG Mea fai pepa Poloketi
O lo'o fa'aaogaina e fai ma mea e mafai ona lolomi, papa lagolago, pepa fa'apipi'i pepa po'o manino Ata overlay i ID fa'apalapala, avanoa, sui auai, faletalimalo, faletupe, felauaiga ma kata atamai.
O lo'o maua PETG pepa mafiafia pepa e maua mai ile 0.05–0.80mm. O laupepa autu masani e mafai ona lolomi e 0.095–0.40mm, a'o manino Ata overlay s e masani ona 0.06–0.10mm. Fa'amaonia le sa'o ma le fa'apalepale mo fa'ailoga oloa ta'itasi.
Ioe, pe a iai itu uma e lua o loʻo i ai mea faʻapitoa i luga ole laiga ma le faʻasologa o le lolomiina e lagolagoina le resitalaina lua itu. O le vaitusi pito muamua e tatau ona fofo atoatoa a'o le'i pasi lona lua.
Leai se fetaui lautele e tatau ona manatu. O le mafiafia o le pepa, malo, lolomi fafaga, vaitusi, vaipuna vaifofo, fofo ma le tuʻuina atu e tatau ona tofotofoina.
Fa'aaogā se vaitusi ua fa'amaonia mo mea palasitika e le fa'afefete. O le oxidative masani, UV -e mafai ona togafitia ma isi faiga atonu e ese le amio, o lea e manaʻomia ai le pipii, faʻamago ma lamination faʻataʻitaʻiga.
O le malosi masani o luga ole laiga e le itiiti ifo i le 38 dynes/cm mo PETG autu ae le itiiti ifo i le 36 dynes/cm mo le itu lolomi o PETG Ata overlay . O le sini mulimuli e tatau ona fetaui ma le faiga vaitusi filifilia ma le metotia o su'ega.
E mafai ona suia togafitiga i luga ole taimi. Teu mea fa'amaufa'ailoga ma fa'amaonia le itu e mafai ona lolomi ma le malosi i luga a'o le'i gaosia, ae maise lava pe a uma ona teuina.
Fa'atatau PETG fa'apipi'i e mafai ona pipii fa'amalama, ae o lamination e leai ni fa'apipi'i fa'apipi'i e fa'apitoa ma fa'apitoa. O vaitusi lolomi, mea fa'afefiloi ma mea fa'apipi'i atonu e mana'omia ai se fa'a fusiua po'o se ufiufi Ata overlay .
PETG / PVC e mafai ona atia'e fausaga tu'ufa'atasia, ae tatau ona fa'ata'ita'i le fusifusia, fa'aiti'i'i, pi'i, puao ma le matua. O nisi tu'ufa'atasiga e mana'omia se mea fa'apipi'i po'o se ufiufi Ata overlay .
E leai se tulaga lautele. Fausia le vevela, mamafa, nofo ma le mālūlū o le taamilosaga e faʻaaoga ai le PETG togi, vaitusi, Ata overlay , faʻapipiʻi ma lolomi.
Leai. Vicat fa'atusatusa amioga fa'amalulu i lalo o se su'ega fa'apitoa. Lamination e faʻalagolago i le faʻaputu atoa, faʻafefe vevela, mamafa, nofo ma malulu.
Ioe. O mea fa'apipi'i, antenna, pu, fa'apipi'i, mafiafia atoa, lamination mamafa ma faitau/tusi fa'atinoga e tatau ona fa'amaonia.
Ioe, e fa'atatau i le viliina o kata-tino, fua o le lua, fa'apipi'i module, fa'amafola o luga, fa'avela vevela ma su'ega eletise.
Ioe. Filifili se maneta talafeagai Ata overlay po'o le fau fau ma fa'ata'ita'i le tulaga fa'amau, fa'apipi'i, fa'amalosi, fa'ailoga ma abrasion.
Leai. Ole ola tautua e fa'alagolago ile fausiaina atoatoa, fa'aoga tulaga, mafiafia kata, lamination, fa'apitoa ma le fa'aalia o le si'osi'omaga. E mana'omia se su'ega fa'ai'u mo le ola.
UV fa'atinoga e fa'apitoa i vasega. Aua ne'i ta'ua le tetee UV i fafo po'o se taimi umi e aunoa ma le tau, suiga o lanu, fa'amatalaga fa'ainisinia ma fa'amatalaga su'ega.
PETG e mafai ona toe fa'aaogaina fa'atekinisi i se vaitafe fetaui, ae o kata fa'amae'a o lo'o i ai vaitusi, mea fa'apipi'i, chips, antennas ma ta'avale atonu e mana'omia ai le aoina ma le fa'agaioiina o tagata tomai faapitoa.
E le o se tagi e le faatuaoia. O fa'atinoga o le si'osi'omaga e fa'alagolago ile puna resini, gaosiga, ola o pepa, mea toe fa'aaogaina, felauaiga ma atina'e fa'ai'uga.
Pa'epa'e, manino, translucent ma aganu'u lanu fa'atasi ai ma lapo'a pepa fa'apitoa e mafai ona fa'atalanoaina e tusa ai ma le mafiafia, sini fa'apitoa, MOQ ma le fa'atinoina o le gaosiga.
Teu fa'amaufa'ailoga, mafolafola, mama ma fa'agogo mai le vevela ma le la. Puipui le pito i luga mai le pefu, maosiosia, suauu ma tamatamailima, ma pepa faʻamau aʻo leʻi lolomiina.
Ioe. Lolomi, fofo, laminate, malulu, tuʻi ma faʻapitoa faʻataʻitaʻiga e faʻaaoga ai mea faigaluega faʻamoemoeina aʻo leʻi faʻamaonia le faʻamatalaga mulimuli.
O le MOQ e fa'alagolago i le mafiafia, lapoa, lanu, luga, togafitiga, autu po'o Ata overlay vasega, tipi fa'aleaganu'u, fa'apipi'i ma mana'oga fa'aletausaga.
Tuuina atu galuega faʻavae, mafiafia, lapopoa, lanu, lolomi faʻapipiʻi, vaitusi, faʻasologa o lamination, faʻamatalaga faʻamaeʻaina o pepa, manaʻoga puʻu poʻo laina, aofaʻi ma le taunuuga.
Fa'afeso'ota'i Wallis Plastic mo PETG offset lomitusi autu ma mea manino Ata overlay mo ID, avanoa, sui auai, faletalimalo, felauaiga, faletupe ma polokalame kata atamai. E lagolagoina e la matou 'au fua fa'aleaganu'u ma lapopo'a, fa'ailoga vaitusi, fa'ata'ita'iga lamination, RFID ma fa'atasi fa'amaneta, fa'amatalaga QC ma sapalai B2B sa'o ile falegaosimea.
